AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
Amp steps near me4/2/2023 ![]() ![]() Disconnect the power cable from the PSU, and wait for 15 seconds.How to run the self-test without the button on the PSU The next step would be to isolate the source of the power failure by disconnecting parts from the PSU, see the Dell knowledge base article Resolve No Power, No POST, No Boot or No Video issues with your Dell Computer. If the BIST LED does not light up, then the power supply is not able to deliver power to the system board and could be caused by any component that is connected to the power supply or the power supply itself.If the integrated self-test LED turns on, then the power supply unit can deliver power to the system board.If the fan is not spinning up properly this should be considered a BIST failure even if the LED lights up. The light should be solid on not flickering or flashing, and the power supply fan should also turn on to speed.Press the BIST button on the computer and check whether the LED lights up. ![]() ![]() How to run the self-test using the button on the PSU To learn more, see the Dell knowledge base article How to Run a Power Supply Unit Self Test On a Dell Desktop or All-in-One Computer. UPDATE: check out the super interesting article by Keith Bloemer about GuitarML, his open source, community driven project that uses machine learning to model real amps and pedals.NOTE: Certain older models of Dell Inspiron, XPS, and Vostro desktop computers may not be equipped with a PSU-integrated self-test. As if you’re making a photocopy of your equipment □ In the near future it will be reasonably easy to profile an amp using these techniques. Guitar players are often extremely conservative.Īnyway, this sounds very promising to me. Because they know they are not using the real thing, their brains doesn’t allow them to enjoy the sound of it. This is often the problem with guitar players who don’t like amp simulation and/or impulse responses. And we need it because our brains are very subjective. In this paper though the blind-test listeners couldn’t tell the difference between the real amp and the black-box version.Ī well done A/B listening test is the best way to achieve objectiveness. Many guitar players find the Kemper profiles extremely realistic. ![]() However in the research paper I found no references to these profiling techniques. And the profiling technique Overloud uses in their TH-U plugin is based on the same technique. If I am correct Kemper Amps is also using black-box techniques for profiling amps. You can find the PDF of the full-text of this research here:Īs an additional bonus the researchers found out that the neural network (black-box) models used way less CPU power to run compared to their white-box virtual analog modelled counterparts.Īll the models included in the listening tests were shown to be capable of running in real-time on a consumer-grade desktop computer, with some of the models only requiring a relatively small amount of the computer’s processing power.īy the way, a mix between white-box modelling and black-box modelling can also be useful. “Deep neural networks for guitar distortion modeling has been tested before,” explains Professor Vesa Välimäki of the work, “but this is the first time where blind-test listeners couldn’t tell the difference between a recording and a fake distorted guitar sound! This is akin to when the computer first learned to play chess.” But as far as I know Neural DSP Technology haven’t used this technique in a plugin yet. The name Neural says it all, since this technique is based on using neural network models. Recently research has been done by Aalto University and Neural DSP Technologies. It uses convolution techniques, but in a non-lineair way, to measure how the hardware changes the input into output. Instead of modelling all the components of a piece of hardware (virtual analog design), modelling the op-amps, the filters and so on (which we call white-box modelling – the ‘we know it all approach’), the black-box method is not trying to find out what exactly is going on inside the box but only tries to find out what comes out of the box. Recently I became aware of a rather new technique for modelling guitar amps, overdrive pedals and other non-lineair equipment. ![]()
0 Comments
Read More
Leave a Reply. |